Balboa ML260 Manuale Utente Scaricare il pdf (Pagina 6)

Page 6 55494_97_A

DIP Switches and Jumper Definitions

DIP Switchbank A Key

A1 ............... Test Mode (normally Off)

A2 ............... In “ON” position, add one high-speed pump (or blower) with Heater

A3 ............... In “ON” position, add two high-speed pumps (or 1 HS Pump and Blower) with Heater

A4 ............... In “ON” position, add four high-speed pumps (or 3 HS Pumps and Blower) with Heater

A10 ............... When switched ON when spa is on, system will enter the Edit Menu for Configuration Settings

Do not start spa with A10 turned on or CFE* error will occur

A11 ............... In “ON” position, enables Special Amperage Rule, see "SA" in Software Configuration section for functionality with your system

............... In “OFF” position, disables Special Amperage Rule

A12 ............... Persistent memory reset (used when spa is powering up) See "Persistent Memory and Powering Up" page

A2, A3, and A4 work in combination to determine the number of high-speed devices and blowers that can run before the heat is disabled. i.e.

A2 and A3 in the ON position and A4 in the OFF position will allow the heater to operate with up to 3 high-speed pumps (or two HS Pumps and

Blower) running at the same time. Heat is disabled when the fourth high-speed pump or blower is turned on.

Note: A2/A3/A4 all off = No heat with any high-speed pump or blower.

*CFE errors are illegal configurations such as a pump and a blower set to run on the same output. The configuration must be corrected before

the spa will operate.

Assignable DIP Switch Key

A5 .............

In “ON” position, Time displayed in 24-hour style (military/European format)

..............In “OFF” position, Time displayed in 12-hour style

A6 and A7

........

See Table 1 for Circ Pump Behavior settings

A8 .............See Table 2 for Spa Light Behavior settings

A9 .............

In “ON” position, Spa Light mode is On/Off

..............In “OFF” position, Spa Light mode is Off/High/Med/Low

B1 .............N/A, must be OFF

..............

See Table 2 for Fiber-Optic Behavior settings

B3 .............

In “ON” position, Option enabled

..............In “OFF” position, Option disabled

B4 .............

In “ON” position, Ozone runs in Filter and Cleanup cycles only

..............In “OFF” position, Ozone runs with Heater Pump

B5 .............

In “ON” position, 1-hour Ozone suppress enabled

..............In “OFF” position, Ozone suppress disabled

B6-B12 ..... Not Assigned

Table 1 Circ Pump

A6 A7 Behavior

OFF OFF No Circ Pump

OFF ON 24-hr Circ Pump

ON OFF 24-hr w-3˚F

ON ON Like P1-low

WARNING:

sSetting DIP switches incorrectly may cause abnormal system behavior and/or damage to system components.

sRefer to Switchbank illustration in this hot sheet for correct settings for this system.

sContact Balboa if you require additional configuration pages added to this hot sheet.

Jumpers Key

J91 .........Jumper on 1 Pin only enables Real Time Clock function, for use with time capable panels.

Jumper on Pins 1 and 2 will disable RTC function, for use with non-time capable panels.

Table 2 A8 OFF A8 ON

B2 OFF No separately-controlled ﬁber light; spa light enabled on both SpaLight and EitherLight buttons; ﬁber

light (not wheel) comes on with spa light (at any intensity)

B2 ON

No separately-controlled ﬁber light; ﬁber light

enabled on both FiberLight and EitherLight

buttons; spa light comes on with ﬁber light

Spa light and ﬁber light each separately controlled;

ﬁber light enabled on both FiberLight and EitherLight

buttons; spa light enabled on SpaLight buttons only

1 2 3 4 5 6 7 8 9 10 11 ... 17 18

Commenti su questo manuale

Nessun commento

Balboa ML260 Manuale Utente Pagina 6

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso Balboa ML260